Barnes 4WD

This is a great kit, made from 2" DOM with a ¼" wall and a high quality poly bushing inner sleeve bore is 9/16" which gives you a very thick wall t...

If you're looking to add protection to your rear axle lower control arm mounts on your Jeep Gladiator JT, then look no farther. Our bolt on lower c...

SCRATCH & DENT PRODUCT This is one of the early designs of our bronco skid plate kit. It works perfectly fine just has a couple extra bolt hole...

This is a replacement ball for the small, 7/8-14 shank Enduro joints. This ball has a mounting width of 2" and a 9/16" bolt hole. This ball is prim...

Have you added an aftermarket bumper to your 2021-Current Ford Bronco and need to relocate your adaptive cruise control? Then we have the product f...

Increasing the strength and rigidity of the rear frame section is recommended when adding bumpers with recovery points or built in tire carriers. T...

A great DIY welding project. Laser Cut and CNC bent here in North Carolina. The same proven designs we have sold and ran for years, now offered...

A great DIY welding project Laser Cut and CNC bent here in North Carolina. The same proven designs we have sold and ran for years, now offered ...

This bumper is compatible with 2007-2018 Jeep Wrangler Models A great DIY welding project Laser Cut and CNC bent here in North Carolina. T...

A great DIY welding project Laser Cut and CNC bent here in North Carolina. The same proven designs we have sold and ran for years, now offered ...

A great DIY welding project Laser Cut and CNC bent here in North Carolina. The same proven designs we have sold and ran for years, now offered...

This skid is designed to be used in our XJ rear 4 link coil spring long arm kit in XJs from 1997-2001. This kit relocates the evap canister and the...

This is the bent D.O.M. tubing that is needed to make the rear upper links for a Jeep XJ 4 link suspension system, it is manufactured from 1-3/4 in...

This is a complete, high quality parallel 4 link suspension kit with all the parts you need to install a parallel four link suspension on your rig ...

A great DIY welding project Laser Cut and CNC bent here in North Carolina. The same proven designs we have sold and ran for years, now offered ...

WELDERS KIT KEY FEATURES A great DIY welding project Majority of the parts are designed with tabs and slots for an easy, straight forward assembly...

High Misalignment spacer reduces a 1 inch bore to a 16mm bolt hole. Mounting width when installed is 74mm with 56° of total misalignment (28° in ei...

High Misalignment spacer reduces a 1 inch bore to a 16mm bolt hole. Mounting width when installed is 70mm with 56° of total misalignment (28° in ei...

If you are looking to add some style, strength, and rigidity to your Bronco suspension we have you covered with our high strength aluminum rear sus...

This bracket set provides a durable yet cost-effective option for routing fluids. Securing the gas fill below the sheet metal flange ensures protec...

Barnes 4wd has designed our Bronco aluminum heim joint steering to be a complete bolt on upgrade to the factory steering. The kit uses a combinatio...

WELDERS KIT KEY FEATURES A great DIY welding project Laser Cut and CNC bent here in North Carolina D-ring mounts are 3/4" thick with a 1" hole ...

WELDERS KIT KEY FEATURES A great DIY welding project Laser Cut and CNC bent here in North Carolina. D-ring mounts are 3/4" thick 3/4" D-ring co...

WELDERS KIT KEY FEATURES A great DIY welding project Laser Cut and CNC bent here in North Carolina. D-ring mounts are 3/4" thick 3/4" D-ring co...

WELDERS KIT KEY FEATURES A great DIY welding project Laser Cut and CNC bent here in North Carolina D-ring mounts are 3/4" thick with a 1" hole ...

SCRATCH AND DENT PRODUCT!!!   These Scout U-Bolt plates are made for 1 3/4" to 2" wide Leaf Springs, if the center locating pin hole is used it wil...

SCRATCH & DENT!!!     If you are looking to convert your 05-up Super Duty Dana 60 axle to an 8x6.5" lug pattern to match your 1 ton rear, we ha...

SCRATCH & DENT!!! THIS ITEM WILL NEED STRAIGHTENED   Are your Jeep Cherokee Nutstrips rotten away? Did your XJ not come with them or simply loo...

SCRATCH & DENT!!!   Looking to add a sweet, beefy JK bumper to your Jeep Cherokee or Comanche? Barnes 4WD has your covered with our Jeep Cherok...

SCRATCH & DENT!!! We understand that not everyone wants to pull everything off of their brand new JL, so we met you in the middle with this w...

Our safety high misalignment spacer is designed for applications with a heim joint mounted in single shear, it is perfect for steering applications...

High Misalignment spacer reduces a 3/4 inch bore to a 1/2 inch bolt hole with 48° of total misalignment (24° in either direction). Mounting width w...

SCRATCH & DENT!!!   This is a replacement tie rod for our Jeep JK 1 Ton 7075 Aluminum Kits. Replacement for: B4WK12300 B4WK12293 B4WK0286

SCRATCH & DENT!!!   Looking to add storage to your Bronco? Then the Barnes 4wd Bronco Center Console Molle Panels are perfect for you. Our moll...

SCRATCH & DENT!!!   Bumpers are made to order and are subject to a 4-6 week lead time once order is placed. Our Jeep JK mini rear bumper was de...

Looking to replace your hard to find shoulder bolt on your Jeeps TJ Rear Sway Bar? Barnes 4wd has the solution for you. We have designed a sleeve t...

Barnes 4wd U-bolts are anything but standard! This u bolt measures 5/8" X 3" X 10" and are a great fit for and axle with a 3" wide leaf spring. The...

4140 CHROMOLY PIN .5" DIAMETER 3.3" USABLE LENGTH   

The Barnes 4WD Dual Pull Winch Plate was an idea born out of necessity. More and more rigs are tackling harder obstacles than ever. With today's su...

If you are looking for complete heavy duty protection for the engine and oil pan on your 2007-2018 4 door or 2 door Jeep Wrangler JK or JKU, with a...