aFe Power

The Sprint Booster is a power converter listed for the Jeep Wrangler JK and Grand Cherokee WK2 with automatic transmission.Fitment: 14-15 Jeep Wran...

The aFe SCORCHER Pro is a handheld performance programmer that loads calibrated tunes for vehicles equipped with aFe POWER products. Tunes are deli...

This aFe Scorcher GT power module increases turbo boost. It includes a case and a wire harness with factory style connectors, and an LED switch let...

The Scorcher Blue is a plug and play electronic power module that works without modifying the engine control unit. A LED switch in the cabin select...

This aFe Rebel Series Cat Back exhaust is made from 409 stainless steel, with mandrel bent tubing that steps from 3in down to 2-1/2in. It ends in d...

This aFe Rebel Series cat back exhaust uses 2.5in 304 stainless steel piping and is finished with black tips.Fitment: 2018+ Jeep Wrangler (JL) V6 3...

This cat back system uses 2-1/2in 304 stainless steel tubing and dual polished tips that exit in front of the rear passenger side tire. It mounts a...

This aFe Rebel Series cat back exhaust uses 2.5in 409 stainless steel tubing and black tips. It attaches at factory mounting locations for a straig...

This Rebel Series cat back system is made from 2.5in 409 stainless steel. Dual polished tips exit in front of the rear passenger side tire. It moun...

This axle back exhaust uses mandrel bent 409 stainless steel tubing and a free flow muffler, with MIG welded construction. It mounts at the factory...

This mid pipe is made from 2.5in 409 stainless steel. It can be used with most aftermarket exhaust systems.Fitment: 2018+ Jeep Wrangler (JL) V6 3.6...

This loop delete down pipe replaces the factory exhaust loop after the catalytic converter, which can contact long arm lift kits. It is built from ...

This Rebel Series cat back system uses 2 1/2in mandrel bent 304 stainless steel tubing that is hand MIG welded. It has a stainless steel muffler an...

This cat back system uses 2.5in mandrel bent 304 stainless steel tubing that is hand MIG welded. It has a high flow stainless muffler, polished tip...

This is the aFe POWER Twisted Steel loop relocation pipe, an exhaust pipe component for the Jeep Wrangler JL with the 3.6L V6 engine.Fitment: 2018 ...

This aFe Rebel Series cat back system is built from mandrel bent 409 stainless steel tubing, 2.5in in diameter. It removes the primary muffler in f...

This Rebel Series cat back system from aFe is made from mandrel bent 409 stainless steel tubing. It has a dual rear exit, removes the primary muffl...

This is the aFe Apollo GT Series 3in Cat Back exhaust system, made from 409 stainless steel.Fitment: 2020 Jeep Gladiator 3.6L. Part NumbersMPN 49-4...

This exhaust uses 2-1/2in mandrel bent 409 stainless steel tubing and a 14in muffler. The Hi-Tuck tailpipe with a black tip adds clearance on steep...

This Rebel Series axle back system from aFe is made from 2-1/2in mandrel bent 409 stainless steel and has a high flow 409 stainless muffler. It end...

This MACH Force-Xp system uses 2.5in mandrel bent 409 stainless steel tubing with a Hi-Tuck tailpipe for added clearance. It uses factory style han...

This aFe MACH Force-Xp axle back exhaust uses 2.5in mandrel bent 409 stainless steel tubing and a polished tip. The Hi-Tuck tailpipe routing adds c...

This aFe Rebel Series cat back exhaust system is made of 2.5in 304 stainless steel and finishes with a polished tip.Fitment: 18-20 Jeep Wrangler JL...

This Rebel Series cat back exhaust is 2.5in 304 stainless steel and comes with a black tip.Fitment: 18-20 Jeep Wrangler (JL) Part NumbersMPN 49-380...

This aFe MACH Force-Xp cat back system uses mandrel bent 409 stainless steel tubing and a transverse muffler, with a high tuck routing. It keeps a ...

This aFe Rebel Series axle back system uses 2-1/2in mandrel bent 409 stainless steel tubing and a 409 stainless steel muffler. It finishes with qua...

This cat back system uses 3in to 2-1/2in mandrel bent 409 stainless steel tubing and a 409 stainless muffler. It finishes with dual 4-1/2in polishe...

This cat back system uses 2.5in mandrel bent 409 stainless steel tubing with a high flow transverse muffler and black tips. It keeps the factory st...

This aFe Rock Basher cat back exhaust system uses 2.5in 409 stainless steel piping. It is listed for the 3.6L V6 Wrangler JL.Fitment: 18-21 Jeep Wr...

This axle back system uses 2-1/2in mandrel bent 409 stainless steel tubing in a Hi-Tuck layout that replaces the low hanging factory muffler assemb...

This aFe Apollo GT Series cat back exhaust system uses 3in 409 stainless steel and a polished tip.Fitment: 2020 Jeep Gladiator 3.6L Part NumbersMPN...

This aFe MACH Force-Xp cat back exhaust uses mandrel bent 409 stainless steel tubing and a transverse muffler in a High-Tuck layout, finished with ...

This is an OE replacement air filter using Pro 5R media, an oiled five layer cotton gauze that gets progressively finer. It has rounded, evenly spa...

This Magnum FLOW Pro 5R filter from aFe is an inverted replacement filter that uses oiled, five layer cotton gauze media. The pleats are rounded an...

This cold air intake has an oil free, 7-1/2in tall inverted conical 360 degree radial flow filter. A one piece 3in mandrel bent aluminum tube carri...

This cold air intake joins the filter to the housing with four captive screws. The Pro Dry S filter has three layers of progressively finer synthet...

This oiled OE replacement air filter has seven layers of cotton gauze and synthetic media. It can be washed and reused, and has tall open pleats an...

This Magnum FLOW inverted air filter uses three layers of progressive synthetic Pro DRY S media that does not need oil. It has rounded open pleats ...

This intake kit has a one piece 16-gauge powder coated heat shield that installs without cutting or drilling. It uses a molded plastic intake tube ...

This aFe Momentum GT cold air intake system uses Pro GUARD 7 filter media and is listed for the 2.0L four cylinder Wrangler JL. The design uses few...

This is the aFe Magnum FORCE Stage 2XP cold air intake with a Pro DRY filter, in black. It uses an oil free, 9in tall inverted top conical 360 degr...

This Stage 2XP cold air intake uses Pro GUARD 7 filter media and has a black finish.Fitment: 18-20 Jeep Wrangler JL 2.0T. Part NumbersMPN 802959545...

This Super Stock induction system from aFe uses a Pro 5R pre oiled, five layer cotton gauze filter. The inverted filter design works inside the fac...

This is the aFe Super Stock Induction System. It uses a Pro DRY S filter with three layers of oil free synthetic media in an inverted replacement f...

This aFe Super Stock induction system uses an inverted replacement filter that fits inside the factory airbox. The Pro 5R media has five layers of ...

This aFe Super Stock Induction System uses a Pro Dry S filter with three layers of oil free synthetic media that needs no oil during maintenance. T...

This is an aFe Quantum cold air intake system with a Pro DRY S filter.Fitment: 18-20 Jeep Wrangler JL L4 2.0L (t) Part NumbersMPN 53-10019D · UPC 8...

This Apollo GT Series Cat Back exhaust uses 3in mandrel bent 409 stainless steel tubing and a single high flow stainless muffler with a deep tone. ...