Military Discount | GOV X

Our heavy duty replacement Jeep TJ/LJ front lower control arm frame brackets are just what you need if you have a damaged or rusted out factory bra...

Our Jeep Cherokee XJ or Jeep Comanche MJ 8.8 Ford axle swap kit contains all the parts that you will need to install a Ford 8.8 axle in the rear of...

This is our Jeep Wrangler JK front frame replacement track bar bracket, this bracket is designed to be a direct replacement for your O.E.M. pan har...

We designed our Jeep TJ or LJ Wagoneer Dana 44 swap kit to make it easy for you to put a Dana 44 in the rear of your Jeep TJ, or LJ.  This kit is d...

High Misalignment spacer reduces a 7/8 inch bore to a 9/16 inch bolt hole. Mounting width when installed is 1-5/8 inches with 52° of total misalig...

Our Jeep JK tube sleeves are designed to add strength to the thin, and bend prone front axle tubes on your Jeep Wrangler.  Today two different type...

If you are looking for a heavy duty upgrade for your existing drag link, then the Barnes 4wd one ton drag link kit is for you!  This is a D.I.Y. ki...

This is a 7/8-18 Left Hand Threads jam nut for use with GM 1 ton tie rod ends or any other tie rod end with the same thread pitch.  These are sold ...

This tube insert is designed to be used with a 7/8" tie rod in tubing with a 1" I.D.  This tube insert differs from our standard insert because it ...

This tube insert is designed to be used with a 7/8" tie rod in tubing with a 1" I.D.  This tube insert differs from our standard insert because it ...

This is a great kit, made from 2" DOM with a ¼" wall and a high quality poly bushing inner sleeve bore is 9/16" or 5/8 which gives you a very thic...

This is a great kit, made from 2" DOM with a ¼" wall and a high quality poly bushing inner sleeve bore is 9/16" or 5/8 which gives you a very thic...

Our single poly bushing kit comes with two bushings and one inner sleeve.  The inner sleeve is 2 inches wide and has a bore of 5/8 inch which gives...

We offer our two bolt flanges in three convenient sizes. These flanges are pre drilled for 3/8" bolts and are made from high strength ¼" thick pla...

This is our centered shackle hanger, this can be used to replace your thin factory hangers or great for a new build. The base is bent from 1/4" pla...

Our 1/4" offset shackle allows you to have a difference of a 1/2" between your leaf spring and spring hanger. These shackles are laser cut from 3/8...

We designed our Jeep JK Superduty Dana 60 swap kit to make it easy for you to put a Dana 60 from a 1999-2004, or 2005-up Ford Superduty in the fro...

Weld washers are intended to increase the strength and durability of mounting holes in bracketry and sheet metal.  This allows you to increase mate...

Repair Weld Washers are intended to repair, and reinforce damaged or deformed mounting holes in bracketry. Drill out the damaged hole to fit the se...

Repair Weld Washers are intended to repair, and reinforce damaged or deformed mounting holes in bracketry. Drill out the damaged hole to fit the se...

Weld washers are intended to increase the strength and durability of mounting holes in bracketry and sheet metal.  This allows you to increase mate...

Weld washers are intended to increase the strength and durability of mounting holes in bracketry and sheet metal.  This allows you to increase mate...

If you are looking for a long lasting precision chromoly rod end, this is the one for you.  This heim joint features a tough PTFE (Teflon) liner th...

If you are looking for a long lasting precision chromoly rod end, this is the one for you.  This heim joint features a tough PTFE (Teflon) liner th...

If you are looking for a long lasting precision chromoly rod end, this is the one for you.  This heim joint features a tough PTFE (Teflon) liner th...

Important notes! - This kit does not include a lifetime warranty. Aluminum is much more elastic that DOM and will serve you better on the rocks,...

We understand that not everyone wants to pull everything off of their brand new JL, so we met you in the middle with this winch mount. This winch m...

If your looking to beef up the drag link on your Jeep JK, this is the upgrade for you. We have taken our famed 7075 aluminum drag link, and have mo...

The Ford Dana 60 flat top truss is ideal for mounting 4 link bracketry to your axle while also adding unsurpassed durability. This kit does require...

Spring Perches are not a one size fits all item. These perches are specially made for a Rockwell square 3 ½” Axle Tube applications and are bent ...

If you are looking for a way to mount a double ended hydraulic steering cylinder to your axle, we have you covered.  This is a DIY kit that can be ...

If you have damaged your thin sheet metal factory shock mounts off road on your 1997-2006 Jeep Wrangler TJ or the 2003-2006 Jeep Wrangler LJ and ar...

If you’re looking to beef up your steering stabilizer, or need a heavy-duty tube clamp for a cage. Barnes 4WD has you covered. Our 6-bolt tube clam...

INSTALLATION NOTES: - This kit moves the track bar bracket forward two inches, therefore steering stops may have to be adjusted to keep pitman arm ...

If you are looking to beef up the drag link on your Jeep JK, this is the upgrade for you. This kit can be put together in minutes and installed on ...

ENDURO JOINT REBUILD VIDEO When Barnes 4WD designed the rebuild-able Offset Enduro suspension joint we combined the best materials, the best manuf...