Military Discount | GOV X

Bumpers are made to order and are subject to a 4-6 week lead time once order is placed. The YJ rear Tail Plate Bumper provides maximum departure an...

Set of 8 studs and nuts to attach high steer arms to kingpin Dana 60 knuckles.  These studs are manufactured from 4140 chromoly for the ultimate in...

Barnes 4WD Single Odyssey PC1500, Group 34/78, and Group 24 Battery Box is a great solution to keep your battery secure even in the roughest terrai...

These flat bottom link tabs are made to weld to any flat surface. These tabs are 3/16" 100,000 min yield steel and have a 1/2" bolt hole. We offe...

Radius Arms are simple and they work! This bracket will allow you to mount a heim joint where the upper control arm on a radius arm suspension moun...

The Barnes 4WD Pro Series GM 14 Bolt measures 50 1/2 inches and are made from a combination of 1/4" and 3/16" steel to keep them light but incredib...

The Barnes 4WD Pro Series Jeep JK Dana 44 Rear Axle Trusses are made from 1/4" steel to keep them light but incredibly strong. This truss is made t...

The Barnes 4WD Pro Series Jeep Dana 30 Front Axle Truss is made from a combination of 1/4" and 3/16" steel to keep them light but incredibly strong...

These 4" Axle Tube U bolt plates are made for 3" width Leaf Springs, if the center locating pin hole is used it will fit a 3 7/8"-4 3/8" axle tube....

The Ford Sterling 10.25 has great ground clearance, strong shafts and it's not too hard to find, but it can still be improved upon. One easy way is...

Our Jeep Wrangler YJ cage stanchions are the perfect base for building a new cage or great for additions to your existing factory cage. These stanc...

If you are looking for the best in a forged polyurethane joint Barnes 4wd has you covered, we designed these to be the strongest joints on the mark...

If you are looking for the ultimate in protection for the front lower control arm mount on your Jeep Wrangler JK, you have found them with our JK f...

These perches are a great upgrade over stock and will not deform under heavy loads.  Cut for a 3 1/4" axle tube diameter 2 1/2" wide leaf spring 5/...

Our bolt on brake line tab was designed with saving time in mind, if you are moving your brake lines or doing a new build simply bolt this in place...

This tube insert is designed to be used with a 7/8" heim joint in tubing with a 1" I.D.  This tube insert differs from our standard insert because ...

This tube insert is designed to be used with a 3/4" heim joint in tubing with a 1" I.D.  This tube insert differs from our standard insert because ...

Barnes 4wd u-bolts are anything but standard! This u bolt measures 5/8" X 3 1/2" X 14" and are a great fit for a GM 14 bolt axle. The biggest misc...

The Barnes 4wd Double Ended Cylinder Tie Rod Kit is designed for the folks running full hydraulic steering with a double ended ram, the kit is comp...

Our Jeep TJ, LJ rear shock mounts are designed to go in place of your factory brackets and are a great option when swapping a DANA 60 or Ford 8.8 i...

Looking for a way to mount your transmission to your tubular cross-member or tube chassis?  Barnes 4wd has the answer with our universal transmissi...

If you are going from heim joints to tie rod ends on your steering or if you are flipping your tie rod to the top of the knuckle, then our tapered ...

Our GM 1-ton tie rod ends are manufactured to be of the highest quality. Barnes 4WD tie rod ends also go above and beyond when it comes to articula...

Our GM 1-ton tie rod ends are manufactured to be of the highest quality. Barnes 4WD tie rod ends also go above and beyond when it comes to articula...

This is a 7/8-18 Right Hand Thread jam nut for use with GM 1 ton tie rod ends or any other tie rod end with the same thread pitch.  These are sold ...

If you are looking for a heavy duty upgrade for your existing tie rod, then the Barnes 4wd one ton tie rod kit is for you!  This is a D.I.Y. kit th...

Barnes offers the most affordable high-quality weld in bungs on the market. No matter the job, have some Barnes tube inserts handy! Built race styl...

If you are modifying your factory frame or building a custom frame our frame fish plates are a must have, they will add the strength you need for y...

This our universal bent steering stabilizer bracket, this bracket is designed to be mounted to a 1.5" O.D. tube in either the horizontal or the ver...

All of our single shackles are made from 3/8" thick Laser Cut plate steel. We offer all our shackles in three different lengths to better suit your...

If you are looking for a serious upgrade for the steering on your Jeep JK, this is the steering kit that you need.  This 1 ton kit uses quality hea...

These flat bottom link tabs are made to weld to any flat surface. These tabs are 3/8 inch thick steel and have a 1/2 inch bolt hole. We offer thr...

This is our Jeep TJ/LJ front frame double shear track bar bracket.  The factory track bar bracket on a TJ is a single shear design and puts a massi...

Our heavy duty replacement Jeep TJ/LJ front upper control arm frame brackets are just what you need if you have a damaged or rusted out factory bra...

Our heavy duty replacement Jeep TJ/LJ rear upper control arm frame brackets are just what you need if you have a damaged or rusted out factory brac...

Bumpers are made to order and are subject to a 4-6 week lead time once order is placed. Our Jeep JK mini rear bumper was designed to be as compact ...