Barnes 4WD

Our Barnes 4WD Cage Tie In Bracket is perfect for any fabricator looking to add strength to their roll cage. Our universal cage tie in bracket is d...

Looking to keep your Jeep JL or Jeep JT Gladiator going no matter how rough the terrain? Then this is the skid for you! Jeep has added a front axle...

Are you building a custom bumper for your rig, or do you want to add a bull bar to your existing bumper? Then this is the product for you. This bul...

This bracket is a perfect addition to any one wanting to put one of our Jeep TJ Bolt On Skid Plate in a Jeep TJ/LJ Rubicon. This bracket is designe...

If you are looking for the ultimate in protection for the front lower control arm mount on your Jeep Wrangler JL or Jeep Gladiator JT, you have fou...

Putting a 2005-up Ford Superduty Dana 60 front axle under your vehicle? Using the factory bushing mounts on the Superduty, this kit will make swapp...

This is a replacement accordion boot for our GM 1 Ton Tie Rod Ends. When the inevitable happens and your tie rod end boots starts cracking and leak...

This is our universal heavy duty 3/4" DIY Drag Link Kit.  This kit uses 3/4" Chromoly Heims and sets you up to run 5/8" bolts at the knuckle and pi...

These hex capture washers are a great way to keep a bolt or nut from spinning on your rig. Simply plug weld the washer in place and around the oute...

Barnes4wd is proud to introduce our Single Jerry Can Mount. This mount is designed to work with a Scepter 5 Gal can and a metal nato style jerry ca...

Whether you are building your XJ for Rock Crawling, Overlanding, Racing, or Support, vehicle organization of gear is always a top priority. This ca...

 Easily dial in coil spring location and angle during mockup. ¼” steel construction 3.5” to 6.5” height from the top on the frame rail 5.5” diame...

In situations where direct replacements are not available these can be a great solution. Providing a solid pre-bent mount with enough material for ...

When attaching tube shock towers to a box frame a stand off is typically needed. These mounts provide the welding surface needed to both weld the t...

 Increase the strength and durability or your axle with this axle truss system. Compatible with 2020 - Current Jeep JT Rubicon Rear Axles  Welding...

Rather it’s in the race rig, trailer, or garage, fluid storage is always a challenge. This bracket incorporates passive retention into the design, ...

WELDERS KIT KEY FEATURES A great DIY welding project. Laser Cut and CNC bent here in North Carolina. The same proven designs we have sold and r...

Piece of mind to take on any terrain that installs in minutes with common hand tools.   Compatible with 2020 - Current Jeep JT 3/16" Steel Bolt On...

If you are looking to convert your Jeep Wrangler TJ or LJ to a long arm link suspension we just made the process a whole lot easier.  Barnes 4wd i...

Intended for use with XJ/TJ/ZJ Models 1/4" Steel Sold In Pairs Welding Is Required

If you're throwing a 1999-2004, or a 2005-Up Super Duty Dana 60 in your Jeep Wrangler TJ, LJ, Cherokee XJ, Comanche MJ, or Grand Cherokee ZJ this i...

Do you have a Jeep XJ that the rear upper shock bolts have rusted and broken when changing your shocks? Then we have the solution for you. We have ...

Bolt on installation. 1 1/4" Shank Tie Rod Ends. 2" OD 7075 T6 Aluminum Steering Links 0-4" lift height compatible. Works with the factory steerin...

Heavy Duty 3/4 - 16 Tube Inserts Barnes offers the most affordable high-quality weld in bungs on the market. Built race style for maximum strength...

Misalignment spacer for 5/8 inch bore. Mounting width when installed is 1 1/2 inches with 28° of total misalignment (14° in either direction) . So...

Misalignment spacer for 1/2 inch bore. 1 1/2" mounting width when installed on a 5/8 x  1/2 heim with 24° of total misalignment (12° in either dire...

We offer our four bolt flanges in three convenient sizes. These flanges are pre drilled for 1/2" bolts and are made from high strength ¼" thick pl...

This inside frame track bar bracket is for those of you running stock width axles, it mounts on the inside of the frame and is formed from of 1/4" ...

This is what we see as the standard Panhard / Trackbar bracket. It has three 5/8 inch bolt holes with mounting positions at, 5.5", 6.5", & 7.5"...

Finally, an all bolt on Disc Brake bracket for the GM 14 bolt single rear wheel full float axles manufactured before 1988, which does not use space...

These inner frame link mount brackets are made to be welded to the inside of your frame. These brackets are made with strength built in due to the...

This is our idea of the correct way to make an Offset Panhard / Trackbar bracket, it seems like 3 out of 4 need to be on the leading edge of the ax...

This is one of our most versatile shock tabs, it can be used for many other applications. This tab is intended to be welded to any flat surface. Th...

Our 1/4" offset shackle allows you to have a difference of a 1/2" between your leaf spring and spring hanger. These shackles are laser cut from 3/8...

Spring Perches are not a one size fits all item. These perches are specially made for Dana 44 applications they are cut for a 2 3/4" axle tube and ...

Spring Perches are not a one size fits all item. These perches are specially made for Early Jeep Narrow width Perches (CJ & M Series) applicati...

Spring Perches are not a one size fits all item. These perches are specially made for 3.0" Axle Tube applications they are cut for a 3" axle tube a...

Coil springs are a very cost effective spring to use when you are building a link suspension system. They are widely used on many different vehicl...

These GM U-Bolt plates are made for 2 1/2" width Leaf Springs, if the center locating pin hole is used it will fit a 2 3/4"-3 5/8" axle tube. Thes...

These CJ & M Series U-Bolt plates are made for 2" wide Leaf Springs, if the center locating pin hole is used it will fit a 2 1/2"-3 5/8" axle t...

This is our flush mount shackle hanger, this can be used to replace your thin factory hangers or great for a new build. The base is bent from 1/4" ...

The Barnes 4WD Cross Member mounting set comes with everything you need to make a cross member both rigid and still isolate vibration. Out kit is m...

3/4"-16 Right Hand Threads per inch jam nut or lock nut.  This will work with our 3/4" Heim joints.  Zinc plated, sold individually.

1 1/4"-12 Right Hand Threads per inch jam nut or lock nut.  This will work with our 1 1/4" Heim joints.  Zinc plated, sold individually.

When it comes to changing axles in a leaf sprung rig you want to get it right the first time, and forget about it. Like all of our products, they ...

When it comes to changing axles in a leaf sprung rig you want to get it right the first time, and forget about it. Like all of our products, they ...

This is our Dodge front Dana 60 specific u-bolt plate. These Dodge Dana 60 plates are for the Dodge axle that the two studs for the u-bolt plate m...

1 1/4-12 Right Handed Threaded shank rod end, 1" bore, ultimate radial static load rating -76,200 lbs.