Coil & Leaf Springs

These Ford U-Bolt plates are made for 3" wide Leaf Springs, if the center locating pin hole is used it will fit a 2 3/4"-3 5/8" axle tube. These U...

This is our Ford front Dana 60 specific u-bolt plate. The drivers side plate is laser cut from 1/2" plate steel, the holes are drilled on one side ...

This is our Chevy front Dana 60 specific u-bolt plate. The passenger side plate is laser cut from 1/2" plate steel, the holes are drilled on one si...

This is our Dodge front Dana 60 specific u-bolt plate. These Dodge Dana 60 plates are for the Dodge axle that the two studs for the u-bolt plate m...

Barnes 4wd u-bolts are anything but standard! This u bolt measures 5/8" X 4 3/8" X 10" and is a great fit a Ford Dana 60 King Pin. The biggest mi...

Spring Perches are not a one size fits all item. These perches are specially made for AMC 20 applications they are cut for 2 1/2" axle tube and are...

Spring Perches are not a one size fits all item. These perches are specially made for Ford Axle applications they are cut for a 3 to 3 1/8 axle tub...

The Barnes 4WD Rear Spring relocation Kit can be used on either a TJ or LJ. This kit can be used to locate the upper coil spring in a vertical posi...

Spring Perches are not a one size fits all item. These perches are specially made for Dana 80 applications they are cut for a 4" axle tube and are ...

Spring Perches are not a one size fits all item. These perches are specially made for a AAM 11.5 applications they are cut for a 4" axle tube and a...

Spring Perches are not a one size fits all item. These perches are specially made for Dana 70 HD applications they are cut for a 4" axle tube and a...

Barnes 4wd u-bolts are anything but standard! This u bolt measures 5/8" X 4" X 10" and are a great fit for a AAM 11.5, Dana 80 or Dana 70 HD. The ...

These coil spring retaining plates will keep your coil springs right were you put them. They are available in two different sizes to fit both 5.5 ...

Our coil spring towers are the best solution you will find for mounting coil springs to the front of your project. These Coil towers are made for ...

Our offset axle Coil spring buckets are a very easy way to gain a few inches of wheel base. Coil springs are a very cost effective spring to use wh...

Our centered frame coil spring bucket is a great platform to attach your coil spring to your frame. These coil spring buckets are made from one pie...

Our offset frame coil spring bucket is a great platform to attach your coil spring to your frame. These offset coil buckets will allow you to eithe...

These 4" Axle Tube U bolt plates are made for 2 1/2" width Leaf Springs, if the center locating pin hole is used it will fit a 3 7/8"-4 3/8" axle t...

These U-Bolt plates are made for 2 3/4" wide Leaf Springs, if the center locating pin hole is used it will fit a 2 3/4"-3 5/8" axle tube. These U-b...

Spring Perches are not a one size fits all item. These perches are specially made for Ford Axle applications they are cut for 3 1/4" to 3 1/2" axle...

Barnes 4wd u-bolts are anything but standard! This u bolt measures 5/8" X 2 1/2" X 10" and are a great fit for and axle with a 2.5" wide leaf sprin...

Lots of people are starting to realize the advantages of a spring under suspension. One big advantage is that it keeps the center of the axle clos...

The Barnes 4WD SUA U bolt plate allows you to set up your spring under suspension in a way that the square u bolt nuts are on top so they are not h...

Frame outriggers are a great addition to our product line up. When you are installing full width one ton axles on a vehicle that has a narrow fram...

These 4" Axle Tube U bolt plates are made for 3" width Leaf Springs, if the center locating pin hole is used it will fit a 3 7/8"-4 3/8" axle tube....

Spring Perches are not a one size fits all item. These perches are specially made for 4.0" Axle Tube applications they are cut for a 4" axle tube a...

Some times a good set of leaf springs can be just a little too flexible and cause leaf spring inversion, this is when the shackle tries to flip ups...

These perches are a great upgrade over stock and will not deform under heavy loads.  Cut for a 3 1/4" axle tube diameter 2 1/2" wide leaf spring 5/...

Barnes 4wd u-bolts are anything but standard! This u bolt measures 5/8" X 3 1/4" X 14" and are a great fit for Ford 8.8 and Dana 60 axles. The big...

Barnes 4wd u-bolts are anything but standard! This u bolt measures 5/8" X 3 1/2" X 14" and are a great fit for a GM 14 bolt axle. The biggest misc...

Barnes 4wd u-bolts are anything but standard! This u bolt measures 5/8" X 4" X 14" and are a great fit for a AAM 11.5, Dana 80 or Dana 70 HD. The ...

Our Jeep TJ rear coil spring brackets are designed to go in place of your factory brackets and are a great option when swapping a Dana 60 or Ford 8...

If you are looking at replacing the front axle coil spring brackets on your TJ, LJ, MJ, XJ, or ZJ we have you covered. These brackets are exact dup...

All of our single shackles are made from 3/8" thick Laser Cut plate steel. We offer all our shackles in three different lengths to better suit your...

All of our single shackles are made from 3/8" thick Laser Cut plate steel. We offer all our shackles in three different lengths to better suit your...

Some times a good set of leaf springs can be just a little too flexible and cause leaf spring inversion, this is when the shackle tries to flip ups...

Some times a good set of leaf springs can be just a little too flexible and cause leaf spring inversion, this is when the shackle tries to flip ups...

This is our centered shackle hanger, this can be used to replace your thin factory hangers or great for a new build. The base is bent from 1/4" pla...

This is our flush mount shackle hanger, this can be used to replace your thin factory hangers or great for a new build. The base is bent from 1/4" ...

Our Jeep Wrangler TJ heavy duty rear frame coil spring brackets are direct replacements for your factory mounts. If you have rusted brackets, damag...

Barnes 4wd u-bolts are anything but standard! This u bolt measures 5/8" X 2-1/2" X 10" and are a great fit for an axle with a 2 1/2" wide leaf spri...

Our spring hangers are simple and strong. They are laser cut from 1/4" plate steel and the bent on a CNC press brake. They are ramped so that you w...

Our spring hangers are simple and strong. They are laser cut from 1/4" plate steel and the bent on a CNC press brake. They are ramped so that you w...

This is our centered shackle hanger, this can be used to replace your thin factory hangers or great for a new build. The base is bent from 1/4" pla...

This is our flush mount shackle hanger, this can be used to replace your thin factory hangers or great for a new build. The base is bent from 1/4" ...

This is our flush mount shackle hanger, this can be used to replace your thin factory hangers or great for a new build. The base is bent from 1/4" ...

Our 1/4" offset shackle allows you to have a difference of a 1/2" between your leaf spring and spring hanger. These shackles are laser cut from 3/8...

Our 1/4" offset shackle allows you to have a difference of a 1/2" between your leaf spring and spring hanger. These shackles are laser cut from 3/8...