OMIX

This is a steel headlight retaining ring that fits either the left or right side. It is sold individually, and two are needed per vehicle. It repla...

This assembly includes the lamp housing and an amber lens. It fits the left or right side, is sold individually, and two are needed per vehicle. It...

This is a left (driver side) tail light assembly with a black housing. It is a direct fit OE style replacement for OE 56018649AC, and the matching ...

This Omix amber side marker lamp mounts on the front driver side of the vehicle and replaces the original lens and light. It is an OE style, direct...

This tail light assembly from Omix is for the passenger side of TJ and LJ models. It replaces OE 56018648AC. For the left assembly, Omix lists 1240...

This is a clear front parking lamp bulb, bulb type 3157. It replaces the OE 3157 bulb and is sold individually as a direct fit OE style part.Fitmen...

This powder coated steel bump stop limits upward axle travel. It fits the left or right side, is sold individually, and two are used per axle. It r...

This yoke U-Bolt kit from Omix is for U bolt style yokes on tapered axle shafts. It includes a pair of U bolts with nuts and washers. It replaces O...

This differential case assembly is for Dana 35 rear differentials with a 3.07 ratio. The kit includes the carrier, spider gears, carrier bearings a...

This Omix greaseable U-Joint is a front axle replacement for Dana 30 axles. It fits either the left or right side and comes with a grease fitting a...

This Omix front axle hub assembly is an OE style, direct fit replacement part. It is covered by a limited 5 year warranty.Fitment: 00-06 Wrangler a...

This Spicer brand carrier assembly is for Dana 35 rear differentials and accepts gear ratios from 3.55 to 4.56. The kit includes the carrier, spide...

This Omix spider gear kit is for rebuilding front differentials on the listed Jeep models. It includes four gears, a cross shaft, thrust washers an...

This Omix pinion yoke is a steel replacement with 26 splines and a strap and bolt style. It is made for the rear driveshaft at the rear axle on Dan...

This flywheel ring gear has a 164-tooth count and is intended for engines used with a manual transmission. It is an OE style, direct fit replacemen...

This chrome lug nut has a 1/2in x 20 right hand thread and is sold as a single nut. It is an OE style direct fit part from Omix and carries a limit...

This Omix front bumper kit is a replacement for the 97-06 Jeep Wrangler. It is sold as a kit under part number 12033.07.Fitment: 97-06 Jeep Wrangle...

This kit includes a stamped steel center bumper beam and a pair of molded bumper extensions, left and right. It is an OE style, direct fit replacem...

This Omix front bumper is a black, OE style direct fit replacement. Front bumper extensions are separate parts, 12031.07 for the left and 12031.08 ...

This Omix steering knuckle is a cast replacement for the left (driver) side. It replaces OE 52067575, and the matching replacement hub assembly is ...

This steering tie rod end has a 7/8in diameter and a left hand thread. It comes with the grease boot, castle nut and cotter pin. Omix lists it for ...

This cast steering knuckle fits the passenger side. The replacement hub assembly is 16705.07. It replaces OE number 52067576 and carries a limited ...

This track bar bolt measures 1/2in-20 x 3in and is for use with aftermarket bars that have 1/2in bushings. It is sold individually and is an OE sty...

This steel pitman arm is made for left hand drive vehicles and replaces OE 52038337. It is an OE style direct fit part with a limited five year war...

This upper ball joint fits either the left or right front side and is sold individually, so two are used per vehicle. The matching lower ball joint...

This replacement push pin is a hood insulator fastener. It is sold individually and replaces OE 6504135.Fitment: 02-21 Jeep TJ, JK, JL, JT, KK and ...

This Omix M6-1.0 hexagon nutsert includes a sealer and serves as a replacement fastener for the listed Jeep models. It is sold individually and rep...

This is a rear back up camera bezel for models equipped with aluminum wheels. It replaces OE 68301879AB and is a direct fit OE style part.Fitment: ...

This replacement front bumper applique has a silver finish. Drilling is required for installation, and it replaces OE 1ML27WS2AA.Fitment: 07-18 Jee...

This front jounce bumper from Omix is dense foam rubber, 3.25in tall and 2in in diameter. It installs into the upper coil spring isolator and fits ...

This is a rear jounce (rebound) bumper that fits either the left or right side. It is sold individually, so two are used per vehicle. It replaces O...

This Omix part is the front bumper impact beam. It is a direct fit, OE style replacement that works with the factory hardware and replaces OE 68003...

This Omix sending unit lock ring is a metal replacement for the fuel tank lock ring on the 87-90 Jeep Wrangler (YJ). It is a direct fit part that r...