APEX Designs USA

A bracket that can be welded onto most single-shear tie rod clamps with a flat mounting surface to provide double-shear mounting capability for the...

An axle-side mounting bracket for the TSR (Through Shaft Ram) high-mount steering system. It installs over the top of the tie rod and works with fa...

A bracket used to fasten Apex hydraulic hoses to the inside of the vehicle frame or any flat surface.Fitment: Universal — no vehicle-specific fitme...

A bracket that mounts Apex hydraulic hoses to the factory (OE) brake line and brake line bracket assembly.Fitment: Universal — no vehicle-specific ...

A mounting bracket used to secure Apex hydraulic hoses to the top of the driver's side lower control arm (LCA) bracket. Note: page title/descriptio...

A set of 3 brackets used to mount the Apex hydraulic hose to the top of the differential cover, securing hydraulic hose routing on the diff.Fitment...

A replacement rod end bolt used for the axle-side connection of the Apex TSR (Through Shaft Ram) steering system. This hardware piece is required w...

A bracket that secures Apex hydraulic lines to the top of FAD (front axle disconnect) housings. It is a component of the TSR High Mount Kit for off...

A hydraulic hose kit for the Through Shaft Ram (TSR) steering system, usable either as a component for the elevated (high-mount) TSR mounting optio...

A replacement spring stop component for the Apex High Flow Push On Chuck that converts the chuck from open-flow to closed-flow operation. The High ...

An adjustable-rate sway bar end link system for the Ram 2500 rear sway bar that lets the driver change suspension stiffness by adjusting air pressu...

A replacement spring stop component used to convert the Apex High Flow Push On Chuck between open-flow and closed-flow modes. The High Flow Push On...

A hydraulic banjo bolt adapter connecting 1/8 NPT threads to a -4 JIC 7/16-20, 37-degree flare fitting, used to attach hydraulic lines to factory s...

A mounting and purge system used to port the factory steering gear on Jeep JL/JT vehicles. It includes table-mounted brackets that hold the steerin...

A through-shaft steering assist ram for Jeep JL and JT vehicles that works alongside the factory electronic power steering system to provide equal ...

A replacement Schrader valve cap for the airLYNX valve assembly, sold as a spare/replacement part.Fitment: For use with airLYNX equipmentMPN: X02-0...

A push-on air chuck with a 1/4 NPT male fitting that connects to Schrader-style valve stems and fully opens the valve (100% vs. standard 50%) for f...

A push-on air chuck with a 1/4 NPT female fitting that connects to Schrader-style valve stems and opens the valve to 100% capacity versus a standar...

A kit of zip ties and hardware used to secure the Remote Fill air lines to the vehicle's sway bar, completing installation of the Remote Fill for a...

A peel-and-stick protective film designed to shield Apex gauge lenses from scratches and damage. It includes a repositionable quick-read indicator ...

An accessory that allows inflation and deflation of airLYNX suspension components from a remote, panel-mounted location such as a bumper or fender....

A pneumatic chuck used to inflate airLYNX suspension components. It seals between the valve stem and the chuck before the core is engaged, allowing...

A carrying case sized for the Apex air-ECO system. It features a heavy-duty zipper, a reinforced bottom liner, padded handles, and reinforced stitc...

A four-tire inflation and deflation system built around 42 feet of 3/8" nylon braided airline that is measured and cut to fit the specific vehicle....

A bolt-on bracket used to mount the Apex Panel Mount fitting to any flat surface. It functions as a mounting solution for panel-mount air fittings ...

This kit provides the components needed to connect an air compressor to an Apex panel mount system. It includes a barbed-to-NPT fitting with an alu...

An inline valve that turns air flow on or off within a 3/8" braided air line system. It is designed to integrate with Apex single/dual/quadAIR infl...

A push-on air chuck that connects to Schrader-style valve stems and fully opens the valve (100% vs. the standard 50%) for faster air delivery. It s...

This connector links 3/8-inch braided hose to Apex female swivel fittings, such as the panel mount and on/off valve.Fitment: Use this fitting to co...

This is a swivel connector with a female 3/8-inch end that connects to a 3/8-inch hose barb, used in pneumatic air line applications.Fitment: Unive...

This fitting adapts an Apex swivel connection to a 1/4 NPT male thread and includes a cover nut.Fitment: Universal — no vehicle-specific fitment.MP...

This fitting flush-mounts Apex 3/8 braided air line to a flat panel, creating a quick-access port for connecting Apex multi-tire air systems.Fitmen...

This fitting is used to repair or extend the length of Apex 3/8 braided air line.Fitment: Universal — no vehicle-specific fitment.MPN: X02-06-011

This is an adapter fitting that converts an Apex Quick Connect male swivel fitting to 1/4 NPT. It is used with the Precision Tire Inflator and Quic...

This is a Y-shaped fitting that connects directly to the Panel Mount Fitting, Precision Tire Inflator, and On/Off Valve. It can also connect to qui...

This is a Y-shaped fitting compatible with Apex 3/8 braided air line, used to split a single air line into two separate feeds for applications such...

This is a replacement installation tool for the Rapid Connect Valve (RCV). It is normally included with purchases of 4 or 5 RCVs; this listing is a...

This kit contains two replacement nuts for use with Apex RPV and RIV products.Fitment: Compatible with RPV and RIV productsMPN: X02-03-012

This is a silicone-based lubricant used for servicing the o-ring seals on RPV (Rapid Precision Valve) products and other o-ring applications.Fitmen...

This kit relocates the factory sway bar 1 inch forward from its OEM position, providing additional clearance for lifted or aftermarket suspension s...

A step drill bit with a 1/4 inch drive used to create properly sized holes in sway bars for nutsert installation as part of the kwikLYNX kit.Fitmen...

A nylon braided air hose made of nitrile rubber with a durable nylon braid, with a 3/8 inch outer diameter and 1/4 inch inner diameter, sold by the...

A kit of hardened washers used as spacers for the AutoLYNX sway bar disconnect system. It includes four washers per side and is intended to correct...

Replacement lower link bolts for the AutoLYNX sway bar disconnect system, specified as M12 x 1.5, 70mm long, matching OE thread pitch. The kit is i...

3/8" swivel to 1/4" NPT (male). This fitting allows you to connect 1/4" NPT to our screw on quick coupler and provides a swivel to the fitting conn...

BE SURE TO SELECT THE CORRECT THREAD PITCH BEFORE CHECKING OUT SKU X02-09-001 - M14x1.5 FACTORY ball joint thread pitch SKU X02-09-007 - M14x2.0 De...

Standard TPMS Mount for Rapid Precision Valve (RPV) Fits TPMS sensors for American made vehicles.

THIS FITTING ALLOWS YOU CONNECT OUR 3/8" BRAIDED AIR HOSE TO 1/4" PUSH TO CONNECT FITTINGS